KnownIssues: Difference between revisions

From Linux/Xtensa
Jump to navigation Jump to search
No edit summary
Line 10: Line 10:
== 128 MB RAM Limit ==
== 128 MB RAM Limit ==


Kernel highmem support has not yet been implemented, thus restricting generally usable RAM to the first 128 MB (starting from physical address zero).  Implementing kernel highmem support should release this limitation, but it isn't yet clear whether an implementation is practical in the presence of cache aliasing (caches larger than 4 x N kB, for an N-way set-associative cache) on RB-200x release or earlier Tensilica processors.
Kernel highmem support has not yet been implemented in the main kernel tree, thus restricting generally usable RAM to the first 128 MB (starting from physical address zero).  Implementing kernel highmem support should release this limitation, but it isn't yet clear whether an implementation is practical in the presence of cache aliasing (caches larger than 4 x N kB, for an N-way set-associative cache) on RB-200x release or earlier Tensilica processors.


== Kernel loadable modules using FLIX with L32R ==
== Kernel loadable modules using FLIX with L32R ==

Revision as of 00:27, 11 March 2013

Known Kernel Issues and Limitations

This page contains recommendations, notes, limitations, and requirements for the development of software on systems using Xtensa processors running Linux.

Eventually all these should be duly reported and tracked in the Mantis bug tracker. For the time being, here are some of the main known issues (this is by no means an exhaustive list!).


128 MB RAM Limit

Kernel highmem support has not yet been implemented in the main kernel tree, thus restricting generally usable RAM to the first 128 MB (starting from physical address zero). Implementing kernel highmem support should release this limitation, but it isn't yet clear whether an implementation is practical in the presence of cache aliasing (caches larger than 4 x N kB, for an N-way set-associative cache) on RB-200x release or earlier Tensilica processors.

Kernel loadable modules using FLIX with L32R

The kernel module loader (for the Xtensa architecture) supports only the limited set of relocations needed for module loading. This includes, for example, relocation of literals referenced by L32R instructions. This loader is not given specific information about any custom TIE configured in the processor, and thus is currently not able to relocate L32R instructions encoded in a FLIX bundle.

To ensure kernel modules load properly, they need to avoid L32R instructions within FLIX instruction bundles.

Existing kernel code does not generate such instructions, so it is not susceptible. However, it is possible to generate FLIX instructions using assembly code, or using the Tensilica XCC compiler. In the case of assembly code, simply avoid using L32R or MOVI instructions within a FLIX instruction bundle, unless a MOVI is known to fit without expanding ("relaxing") into an L32R instruction. In the case of XCC, pass the -mno-flix to the compiler (xt-xcc) to avoid generating FLIX bundles.

Note: The use of Tensilica software tools (including XCC) for Linux development is described in the Tensilica OSKit Guide, available from Tensilica.

Debugging Kernel Loadable Modules

Debugging loadable modules isn't easy, a few pointers mentioned here might save you some time. There is a mechanism that Amit Kalie mentioned on his KGDB webpage on loading the module symbols into gdb while loading a module Debuging init_module.

The insmod command has a --map option that dumps the module component offsets needed by Amit's approach. Unfortunately the initial Xtensa buildroot snapshots have a version of insmod that doesn't provide this option. Also, while debugging the kernel it's not convenient to run insmod on the console of the target.

A workaround to this problem is to hack the kernel module.c file and enable debugging.

   #if 1
   #define DEBUGP printk
   #else
   #define DEBUGP(fmt , a...)
   #endif

This will enable module.c to print the module section addresses. You then just list them in the gdb add-symbol-file command using that command's section (-s) options. Note that the .text section is specified without using the -s option: its address is given alone before any -s option.

   final section addresses:                  [Kernel Console Log/Output]
       0xc02a9098 .note.gnu.build-id
       0xc02b1000 .init.literal
       0xc02a7000 .text
       0xc02b11d8 .init.text
       0xc02a90bc .rodata
       0xc02a92c4 .rodata.str1.4
       0xc02ac27c .data
       0xc02ac640 __param
       0xc02ac668 .gnu.linkonce.this_module
       0xc02ac76c .bss
       0xc02aaf0c .symtab
       0xc02ab8fc .strtab
   add-symbol-file /export/src/Transwitch/a2000_src/a2000_src/Linux_atlanta/ctlm-cpe/drivers/ctlmeth/ctlmeth.ko   \
       0xc02a7000                           \
       -s .data 0xc02ac27c                  \
       -s .init.text 0xc02b11d8             \
       -s .bss 0xc02ac76c                   \
       -s .init.literal 0xc02b1000          \
       -s  .rodata 0xc02a90bc

You likely want to compile your modules unoptimized and unstripped to facilitate debugging and provide the path to the module source to gdb with the dir command. For example:

   dir /home/pdelaney/src/Transwitch/a2000_src/a2000_src/Linux_atlanta/ctlm-cpe/drivers/ctlmeth/